If you need to replace an old toilet, repair a toilet flange or install new bathroom flooring, you’ll need to know how to remove a toilet. Removing a toilet is a relatively simple project that most DIYers can tackle either alone or with a helper.
They often ask if they should remove the toilet before installing a new bathroom floor. While it is possible to install a new linoleum or ceramic tile floor without removing the toilet, it is not recommended and actually can increase the labor involved in the project.
Start by removing all the grout using a grout saw, rotary cutter, oscillating tool, or utility knife. Next, position a chisel in the grout line under the bottom of the tile, and tap it gently with a hammer to see if the tile will pop loose (be careful not to chip or crack the adjoining tile).
How much will a plumber charge to install a toilet? Toilet installation costs range from $224 to $531, with the national average at $372. Plumbers can charge anywhere from $65 to $250 per hour for labor costs.
Yes. A toilet is part of your plumbing system, and needs to be installed by a licensed and qualified plumber. If you are undertaking a complete bathroom renovation and replacing your toilet as part of this job, your bathroom renovator needs to be appropriately licensed and use a plumber for this job.
Like a standard drain snake, the toilet auger has a cable that rotates by a handle. But this tool is specially designed for toilets, with a hollow tube attached to an elbow fitting covered by a rubber sleeve that protects the toilet bowl from scratches.
All things being considered, the time it takes to remove a toilet varies from 15 to 30 minutes, depending on the condition of the toilet parts and fittings. Below are the steps you’ll need to follow to completely remove your old toilet from the floor and sewer pipe.
Whenever you remove a toilet for any reason, you will need to replace the wax ring seal between the toilet and the toilet flange (sometimes called a closet flange) attached to the floor. A wax seal is used because it resists mold and bacteria and retains its sealing ability after years of use.
Removing the Toilet
They aren’t as easy to cut into rounded shapes as vinyl tile is, so they often require that you remove the toilet. … It’s better to leave the toilet where it is and work around it if you can.
If you are installing vinyl planks in a bathroom, you may need to temporarily remove the toilet or you can install around it. If the subfloor is unlevel, you can fix low spots with a self-leveling product and sand or grind down high spots. Tip: Do not try to sand down old vinyl flooring, as it may contain asbestos.
Stuffing a rag into the drain opening will prevent sewer gases and fumes from entering the drain pipe. Before installing a new toilet, you should remove the rag. The wax ring on the toilet horn needs to be properly installed.
All you need are a few hours, a helper and the right tools and toilet parts for the job. Before you begin learning how to install a toilet, choose your new toilet, and if you aren’t replacing an existing toilet, make sure you have plumbing ready for the new installation.
Again, the price will vary depending on the difficulty of your job. On average, most toilet replacements cost between $200 and $400 as a general rule. However, with some luck, a simple installation can cost between $150 and $250 to replace your existing toilet.
Typically, toilets need replacement after 25 years of use so this can be considered the average toilet lifespan. Some would argue that the porcelain toilet itself has a much longer, and even unlimited, lifespan and that it’s only the components inside that need repairs and replacements.
|National Average Cost||$170|
|Average Range||$150 to $180|
If you are in desperate need of stopping a constantly flushing toilet or leaks, a handyman can take care of this for you. If the plumbing issue is more complex than a leak or you need a toilet repaired, that’s when it’s time to call in the professional plumber.
One of the most common tools for unclogging a toilet is the toilet auger. Also known as a water closet auger or plumbing snake, this device is designed to move through the drain of the toilet to remove the clog or obstruction that’s causing the stoppage. … Augers are usually made of metal.
Yes, you do have to plug (cover) the hole to keep sewer gases from coming through.
Sewage gases are emitted from open toilet drain pipes and definitely can be harmful, especially over a prolonged period, particularly for children and those with breathing ailments. Plugging or covering the pipe immediately and working efficiently in a well-ventilated space can minimize any effects.
Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?
In many cases, a constant urine smell is likely due to a leaking seal, which is located under the toilet and seals the point between the toilet and the drain. Improper installation and general wear and tear can cause the seal to leak.
Using a wax-free seal makes clean up easier and there’s less room for error. … If you need to remove the toilet base with a wax ring, you’ll need to purchase another ring to reinstall the toilet. When you use a wax-free seal, it’s reusable as long as it’s in good condition.
how to remove a toilet permanently
how to remove a toilet bowl
how to remove a toilet to unclog
how to remove and install a toilet
how to remove a toilet seat